driver board

Every drive board can drive a diode laser. The function of control unit single chip in the driver board is to control the aging process of 16 laser diodes in current mode or in output power mode.

驱动板的控制单元-单片机实现对16个半导体激光器的老化过程进行监控，从而使激光器工作在上位机所指定的恒流状态或者恒功状态下。

PCI Bus-Based WDM Device Driver for Motor Control Board

PCI总线电机控制卡的WDM设备驱动程序设计

The paper introduces a driver board for intelligent traffic machine based on MCS-51 and CPLD.

介绍了基于MCS-51和CPLD的新型智能信号机驱动板设计。

The driver board and display board was designed by our self.

驱动板和显示板是自行研制的，显示板是由红绿两色LED材料组成的发光阵列。

The fuzzy on-line control system of close-loop is made up when the power driver board is added in primary on-line checking system.

在原来在线检测的硬件系统中加入功率驱动板，就构成了闭环模糊在线控制系统。

The system hardware includes main control board, display and button board, and motor driver board.

系统的硬件电路板主要包括主控制板、显示按键板、电机驱动板。

Then, according to the function of experiment equipment, we put forward the experiment scheme based on the power unit controller and driver board, based on the power unit, based on the high voltage inverter experiment system.

随后，根据该工装的功能，提出了基于功率单元控制驱动板件、基于功率单元、基于高压变频器实验系统的实验方案。

The control wires are connected on the user terminal block of the driver board.

在过载情况下，导电板将与端子分离，关掉开关。

Motor driver board is connected directly with the two motors, including DC servo motor driver circuit, DC step motor driver circuit and over-current protection circuit.

电机驱动板是系统直接连接两台被控电机的执行部分，主要包括直流伺服电机驱动电路、步进电机驱动电路和过流保护电路。

The programable CCD driver introduced in the paper is a linear CCD driver printed circuit board, which small in size, common in useageqn and stability in performance.

本文介绍的可编程CCD驱动器是一种通用、小型化、性能稳定的线阵CCD驱动电路板。

The dynamic sand table include a total of 15 × 21 pixels point, so with a 15 × 21 sets of driver and control board, PC control system is based on VC++ development.

本项目动态展会沙盘的样机共有15×21个像素点，所以配备了15×21套控制板与驱动板。上位机控制系统基于VC++开发。

Design for Timing Relay Driver Board Based On ARM

基于ARM的定时继电器驱动模板的设计

What's more, WinCE operating system based on PCM-3350 is configured, driver of data acquisition board and application software are programmed.

并且实现了基于研华PCM-3350操作系统的定制、振动信号采集卡驱动程序的开发和振动分析软件的设计与编程实现。

The driver board can be applied to any intersection because of combining traffic signal control and safety detection.

该设计实现了灯色控制和安全检测功能，扩展性强，适用于多种类型的交叉口信号控制。

And this paper analyze the transformation of the coordinate system in motor control, vector control, and space vector pulse width modulation theory. Secondly, this paper design the hardware part of the AC servo system, including power driver board and DSP control board.

并详细解析了电机控制中的坐标系变换、矢量控制理论及空间矢量脉宽调制理论。二、设计交流伺服系统的硬件部分，包括功率驱动板和DSP控制板。

The main circuit of the System is composed of voltage rectifier and inverter circuit, the control system is mainly composed of the power supply and driver circuit board, the central control board, the detection circuit board, and other auxiliary circuit.

系统主电路由电压型整流电路和逆变电路组成，系统的控制电路主要由电源及驱动电路板、核心控制板、检测电路板以及其他辅助电路等构成。

The driver board of permanent magnet brushless DC motor in EPS system and its three working modes corresponding to control strategies were introduced.

最后，给出了一整套EPS系统ECU硬件设计方案，详细介绍了永磁无刷直流电动机的驱动电路和电动机与EPS系统控制策略相对应的三种工作模式。

Completing detail design of analog control circuits for rotational speed of dc motor, power driver circuit board and multifunction-integrated control circuit board were developed.

完成电动机转速的模拟电路控制方案的详细设计。开发出电动机功率驱动板、集成多种实验电路的一体化控制板。

The legacy serial driver that drives this board's UART channels can send and receive data from the BlueZ UART transport driver.

这个母板的UART通道使用的传统串行驱动程序可以从BlueZ UART传输驱动程序上收发数据。

Developing Device Driver for Multi-COM Board under Windows NT

WINDOWS nt下多串口卡驱动程序的开发

During the driver development, it first tells about the choice of the develop tools and driver models, and then depicts the process of the developing and debugging with WDM driver for the interface board.

在驱动程序的开发部分，首先介绍驱动程序开发工具及模式的选择，然后详细讲述了WDM模式的驱动程序开发及调试过程。

Design and Implementation of High-end LCD TV Driver Board

高端液晶电视驱动电路的设计与实现

Though the calculated results, the IGBT option are verified right. A high-voltage IGBT driver board is designed and produced. Its control software, control circuit and functional description then are described.

设计并制作了高压IGBT驱动板，对其控制软件、控制电路及功能进行介绍。

Chapter 4 develops a WDM driver for the PCI board.

第四章针对PCI板卡设计了相应的WDM驱动程序。

Fault Diagnosis of CD-ROM Driver's Printed Circuit Board Based on Information Flow Model

基于信息流模型的光驱电路板故障诊断